Step Plumbing Guide for Bathtub Installation
Step Plumbing Guide for Bathtub Installation
Blog Article
Listed here in the next paragraph you'll find more worthwhile additional info involving A Step-by-Step Guide to Installing a Bathtub.

Mounting a bathtub isn't exactly rocket science, but it does call for strong plumbing, carpentry, and sometimes, tiling skills. Replacing an old bath tub with a brand-new one is likewise a reasonably difficult job. If the old tub is readily easily accessible, the job can relocate easily; if you have to open up a wall surface to get rid of the old tub and position the brand-new tub, the task is much harder. In either case, the job is within a home handyman's abilities, although you will certainly need a helper to move out the old tub and also embeded in the new one. See to it you have actually qualified yourself for the job as well as are comfortable attempting it. Rather than employing a contractor to take over a halfway-completed job, it is far better to consider using one before you begin. Chances are you might require a professional plumber to make tube connections.
This post will help you set up a brand-new bath tub in your bathroom if you have actually already acquired a brand-new bathtub and don't need to change the plan of your previous water supply pipelines.
Your tools and also product list should comprise the following:
Planning for the Setup
Firstly, the sustaining framework provided with the bath needs to be fitted (if required) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to make certain that if the tap features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to stop strain on the bath tub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its last position.
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, after that the first thing you ought to do is separate the water supply. After doing so, switch on the taps to drain pipes any water staying in the system. The process of eliminating the existing taps can be quite bothersome as a result of the restricted access that is often the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the faucets. Have a fabric ready for the remaining water that will come from the pipes. As soon as the supply pipes have been gotten rid of, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any old sealing compound.
Before moving on to fit the new taps, contrast the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Using both wood boards under its feet, place the tub in the required placement. The wood boards are useful in equally spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 little points.
The following objective is to ensure that the tub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the bathtub until the level checks out degree.
To mount taps, fit the bottom of the outermost flexible tap connector to the appropriate supply pipe by making a compression sign up with; after that do the very same for the various other tap.
Turn on the water system as well as check all joints and new pipework for leaks as well as tighten them if necessary. Fill the bath tub as well as additionally inspect the overflow outlet and also the normal electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the tub needs to wait until the bathtub has been utilized at the very least when as this will settle it into its final setting.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the mounting hole in the bath/basin making certain that the washers are in area in between the tap and the sink. Safeguard the tap in position with the maker supplied backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The former type needs to be connected to the tap ends initially, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom fulfills the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to fracture an inflexible seal, creating the water to pass through the wall surface between the bath and also the tiling, bring about complications with wetness and also feasible leaks to the ceiling listed below.
You can select from a range of coloured sealers to blend in your fixtures as well as fittings. They are marketed in tubes as well as cartridges, and also can sealing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched paper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealer can break relatively very early if you do not take into consideration this movement before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly readily available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water-proof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

We were shown that article about Installing A Bathtub through someone on another web blog. Are you aware of anybody else who is enthusiastic about the niche? Do not hesitate to share it. I cherish reading our article about A Step-by-Step Guide to Installing a Bathtub.
Quality and quick, dial! Report this page